• Detachable liners should be removed from the shell and laundered separately.
• All closures should be fastened: VELCRO® hook tape covering VELCRO® loop tape, hooks and dees fastened, zippers zipped and snap's closed. It is imperative that you cover the hook portion of all hook and loop to prevent snagging during laundering.
• We recommend a front loading washing machine, which does not have an agitator, and preferably one that is designated specifically for cleaning turnouts. A stainless steel tub should be utilized if available.
• We suggest using a laundry bag to protect the inside of the washing machine from the hardware (and to protect the hardware from the agitator of a washing machine when using a top load model).

Machine Washing: The special fabrics that make up your Globe Fr protective clothing contain inherent flame and heat resistance properties, which cannot be washed off or worn out. However, given the nature of the contaminants to which fire fighters are exposed, we recommend that you never, never, use the same machine that you do your home laundry in. When machine washing, always prepare the clothing as directed, by fastening all closure systems. Use warm water, a normal cycle, and a machine setting of 100 rPm’s or less. Following each complete wash cycle, thoroughly rinse your garments; we recommend a double rinse with clear water.

Protective clothing should always be washed separately in a laundry bag; do not overload the washing machine, do not use softeners, and NEVER use chlorine bleach. it is important that the water temperature not exceed 105°F. We do not suggest machine drying; our recommendation is to hang in a shaded area that receives good cross ventilation or hang on a line and use a fan to circulate the air.

Cleaning Agents: Cleansers generally fall into two categories, detergents and soaps. Of the two, detergents make the best cleansers because they are formulated to contain special agents that help prevent redeposition of soil. Soil redeposition is soil which is first removed from a laundered article, but later in the same wash cycle is redeposited as a thin soil film on the entire surface of the article. All cleaning agents are clearly labeled as being either detergents or soaps; and we recommend using liquid detergents, since they are less likely to leave any residue on the clothing. One example of a well known liquid detergent would be tiDe®. Finally, it is important that the cleaning solution have a pH range of not less than 6.0 pH and not greater than 10.5 pH.

Spot Cleaning and Pretreating: Precleaners can be used to clean light spots and stains on protective clothing. Squirt the precleaner onto the soiled area and gently rub fabric together until a light foam appears on the surface; this foam should be completely rinsed off with cool water prior to washing. A soft bristle brush, such as a toothbrush, may be used to gently scrub the soiled area for approximately one to one and a half minutes. An alternative method would be to pretreat the garment by applying liquid detergent directly from the bottle onto the soiled area and proceed as with precleaners. Any spot cleaning or pretreating should be followed by machine washing prior to field use.

Special Cleaning Compounds: Since Globe is in the business of producing protective clothing and not cleaning agents, we are not able to "endorse" any of the special compounds that are being advertised for the fire service, such as Winsol or Smoke Out. However, we would recommend that each department interested in these specific cleaning agents contact the manufacturers directly and make your own determination as to suitability.

Dry Cleaning: the protective qualities of your Globe turnout clothing will not be adversely affected by dry cleaning. However, some dry cleaning methods can cause deterioration to the trim and is therefore not recommended.

Removing Oil or Tar: Oil based soils such as motor oil and tar can be removed with solvents such as varsol™ prior to washing, according to DuPont, producers of the NOmeX® fibers. However, they do add the cautionary statement that the garment must be thoroughly washed and rinsed to insure that all residual solvent is completely removed. they also point out that coated material should never be dry cleaned. You must always avoid using solvents on the leather or reflective trim.

Bleach: One of the most often asked questions concerns the decontamination of a turnout system, especially with chlorine bleach. UNDER NO CIRCUMSTANCES should chlorine bleach be used on fire fighters' clothing; most systems contain KEVLAR® fiber, which is completely destroyed by exposure to bleach. if it is absolutely essential that a bleach be used, we recommend 1/2 cup of liquid oxygenated bleach to one cup of detergent.

Trim: 3m, the manufacturer of SCOTCHLITE™, recommends that the following guidelines be used for their product: (1) Damp wipe, using warm water and mild detergent. rinse thoroughly, dry with a soft cloth, or allow to air dry. (2) if you choose to machine wash, use warm water. (3) Do not dry clean. they also warn that many common fire ground contaminants can attack the silver stripe of their triple trim product, causing it to fade, either immediately or over time. they recommend that whenever any type of trim contamination is suspected, the trim should be thoroughly rinsed at the scene as soon as possible, followed by normal laundering.

Decontamination: For extreme contamination with products of combustion, fire debris or body fluids, removal of the contaminants by flushing with water as soon as possible is necessary, followed by appropriate cleaning. in the case of blood born pathogens, recommended decontamination procedures include using a .5 to 1% concentration of lYSOL®, or a 3-6% concentration of stabilized hydrogen peroxide. liquid glutaraldehyde, available through commercial sources, will also provide high to intermediate levels of disinfectant activity. Decontamination may not be possible when protective clothing is contaminated with chemical or biological agents. When decontamination is not possible, the garments should be discarded in accordance with local, state and federal regulations. Garments that are discarded should be destroyed.

Hand Washing: Hand washing was once thought to be the least abrasive method of laundering, and allowed the user to pay special attention to those areas that required it. the industry now recognizes that hand washing is generally not able to remove the ground-in soil embedded in the material fibers and usually only serves to remove surface dirt. However, in the event that you do not have access to a washing machine and must hand wash your garment, remove your liner system and lay the outer shell on a nonabrasive hard surface. Using a soft bristle scrub brush and a detergent (not soap), clean your garment by making circular motions with the brush, forming progressively larger circles until the entire surface has been washed. You must then rinse the shell, using clear water, to insure that all of the detergent has been removed. We recommend that you rinse the entire garment several times to avoid any possibility of soil detergent residue.

Outside Cleaning Assistance: One final question we are often asked is whether the gear can be or even should be cleaned by a professional. We are aware of several outside agencies who specialize in the cleaning of turnout clothing and just as Globe is the expert in the cutting and stitching of protective clothing, these facilities are the experts in cleaning. Since we have no control over any of their processes, we obviously cannot endorse or authorize any one of these services over another; however, we do believe they offer a valuable service and we encourage our customers to contact any of these outside cleaning facilities to determine if they are able to meet the fire department needs. Some possible questions to ask would be if they have ever had third party training or testing, if they provide any warranties on their services, and whether they are able to give any guarantees concerning the effectiveness of their cleaning.

In caring for your protective clothing, you must always consider each individual layer when deciding how to clean. We do encourage every department to keep their clothing clean and to routinely inspect and repair as needed. Clean protective gear is lighter in weight, lasts longer, and is more visible than dirty turnout gear. Having dirt, soot, and other debris clinging to your gear represents a true safety hazard.